The NIJ 0101.06 standard is a comprehensive standard for testing the protective values of ballistic armor such as that used by law enforcement and military personnel. To qualify under this standard, ballistic armor must pass a series of rigorous performance tests to ensure it meets expectations.
Ballistic armor is classified by level of protection, with higher levels offering increasingly effective protection against penetration and blunt trauma impact from larger caliber projectiles; To pass certification, a vest must prevent penetration of the test bullet at the test firing velocity and, most importantly, must prevent deformation as a result of blunt force trauma to the test surface. Soft armor (such as concealable vests worn by law enforcement) consists of Tier II-A, Tier II, and Tier III-A, and is intended to primarily protect against small arms fire. Hard body armor consists of rigid insertable plates and is rated Tier III or Tier IV, for protection against rifle rounds.
The important points of the NIJ standard can be explained by noting the changes in the test requirements of the NIJ standard 0101.06 and the interim standard 0101.05; After reviewing the tests of the previous standard, as well as the performance in the field, the National Institute of Justice has determined that more rigorous test requirements are needed to ensure a minimum useful life of five years and to protect against larger and faster bullets. than in previous evidence.
Per NIJ Standard 0101.05, for tests IIA through IIIA, a total of six panel samples were required for testing purposes. Each panel was to be a standard size, with six shots per panel and a minimum shot spacing of 2 inches. Two shots (#4 and #5, specifically) were to be fired at a 30 degree angle from the armor, to test angled hits. To test the effects of water on the material, the armor was subjected to a six minute spray down prior to testing. All test shots were fired in areas a minimum of 3 inches from any edge. Four ballistic limit tests were performed to test its resistance to penetration; Two back face signature tests were performed to test the deformation of a test material (soft clay) behind a point of impact, with a maximum allowable deformation depth of less than 44 millimeters. The bulletproof vest would fail the test if it allowed further deformation of the test bullets, or if the first test bullet completely penetrated the ballistic armor.
The NIJ 0101.06 standard provides more rigorous testing of these requirements. Specifically, 28 test samples are required: 22 large samples and 6 small samples. Each panel still gets six test shots, but the spacing is more rigidly defined: Shots one through three are a minimum of two inches apart, with a minimum distance from the edges of 2 inches. Shots 4 through 6 must be grouped in a circle with a maximum extension of 3.94 inches. Shot 4 is still tested at a 30 degree angle, but Shot 5 is tested at a 45 degree angle. The wet test is performed by fully immersing the armor for 30 minutes. Ballistic limit tests are performed in both the first and second rounds per type, with ten tests performed per type. The back face signature deformation test requires three measured deformations of less than 44 millimeters, with a second measurement of any result greater than 40 millimeters, and one outlier is allowed. Failure occurs if major deformations are recorded, or if the armor is pierced by any portion of the projectiles tested.
The NIJ 0101.04 standard required vests to be certified to Level IIA to withstand the test of a 9mm round traveling at a relative velocity of 1120 feet per second and a .40 caliber round traveling at 1055 fps. Tier II armor had to withstand a 9mm round traveling at 1205 fps (+/-30) and a .357 magnum round traveling at 1430 fps. Level IIIA armor was required to stop a 9mm round at 1430 fps and a .44 magnum round at 1430 fps.
The NIJ 0101.06 standard increases the requirements at all levels; Armor to be classified as Tier IIA must now withstand a 9mm round at 1225 fps and a .40 caliber round at 1155 fps. Tier II armor should now support a 9mm round at 1305 fps, as well as a .357 magnum at 1430 fps. Tier IIIA armor should now be able to withstand a .357 SIG round at 1470 fps, as well as a .44 magnum at 1430 fps. All of these tests must be performed in accordance with the requirements listed above.
Additionally, NIJ Standard 0101.06 tests for the effects of environmental conditioning of water, long-term use, and temperature exposure. These tests place a batch of eight panels (six large and two small) in a rotary dryer at 149 degrees Fahrenheit with 80% relative humidity. This batch is cycled through 72,000 cycles at five revolutions per minute over a period of approximately ten days, then removed and tested against both threat calibers at a reduced test rate (Level IIA requires testing of 9mm rounds). at 1165 fps and .40 caliber rounds at 1065 fps after conditioning, Tier II requires testing of 9mm rounds at 1245 fps and .357 magnum rounds after conditioning, Tier IIIA requires testing of . 357 at 1410 fps and .44 magnum rounds at 1340 fps after conditioning).
The level of protection one wears is generally based on the need for concealability, comfort, and overall protection. Tier II-A is the thinnest and lightest armor available and stops the penetration of most threats, but is less effective against blunt trauma injuries. Tier II armor provides a balance between blunt trauma protection against high velocity rounds, cost, and thickness while remaining concealable. Tier III-A armor provides the best protection in soft armor and minimizes blunt trauma injuries to the wearer, allowing you to respond more quickly to imminent threats, but is less concealable, heavy, and more expensive.